10.1.1.1 Router Login: Access Admin Panel & WiFi Settings

by Tommy N. Updated Apr 24, 2026

10.1.1.1 is a private IP address used as the default gateway by Telstra, Australian ISPs routers. Use the 10.1.1.1 login page to access your router admin panel and configure WiFi settings.

Figure 1 — 10.1.1.1 Login Admin - Router Login & WiFi Settings Guide

Note: If 10.1.1.1 doesn't work, your router may use a different IP. Try 192.168.1.1, 192.168.0.1, or 10.0.0.1 instead. You can also find your router's IP address on any device.

10.1.1.1 Default Login Credentials

Username	Password	Router Brand
admin	admin	Telstra, Australian ISPs

If these don't work, check our default router passwords list. You can also factory reset your router to restore defaults.

How To Login to 10.1.1.1

Connect to your router — via Ethernet cable or WiFi. You must be on the router's local network.
Open a web browser — type http://10.1.1.1 in the address bar and press Enter.
Enter your credentials — use the default username and password from the table above.
Access the admin panel — you can now change WiFi settings, security options, and more.

Can't access 10.1.1.1? Make sure you're connected to the router directly (not a WiFi extender). Verify 10.1.1.1 is your actual gateway IP using our router IP finder guide.

What Can You Configure?

WiFi Settings

Change WiFi name (SSID) and password
Switch wireless channel to reduce interference
Set encryption to WPA2 or WPA3
Set up a guest WiFi network

Security

Block unwanted devices from your network
Configure firewall and access controls
Set up parental controls

Advanced

Port forwarding for gaming or servers
QoS bandwidth prioritization
VPN, DDNS, and static route configuration
Factory reset and firmware updates

10.1.1.1 vs Other Router IPs

IP Address	Common Brands
10.0.0.1	Xfinity, Comcast, Piso WiFi
192.168.0.1	D-Link, Netgear, TP-Link
192.168.1.1	Linksys, Asus, Cisco
192.168.10.1	TRENDnet, TP-Link
192.168.1.254	AT&T, BT Home Hub

Video Tutorial

Pro Tip: Always change your router's default admin password immediately after first login. Default credentials are publicly known and a major security risk.

Key Takeaways

Most routers use admin/admin or admin/password as default credentials
Always change the default password after your first login
If the IP doesn't work, find your actual router IP
A factory reset restores defaults if you're locked out

Frequently Asked Questions

What is 10.1.1.1 used for?

10.1.1.1 is a private IP address used as the default gateway for Telstra, Australian ISPs routers. It lets you access the router admin panel to change WiFi and network settings.

What is the default password for 10.1.1.1?

The most common default login is username: admin and password: admin. Check the sticker on your router if this doesn't work.

Why can't I access 10.1.1.1?

Common causes: you're not on the router's network, the IP is mistyped, or your router uses a different gateway. Try finding your actual router IP address.

How do I reset my router password?

Hold the reset button on your router for 10-15 seconds to restore factory defaults. See our reset guide for details.

About Tommy N.

Tommy is the founder of RouterHax and a network engineer with over ten years of experience in home and enterprise networking. He has configured and troubleshot networks ranging from simple home setups to multi-site enterprise deployments, with deep hands-on experience in router configuration, WiFi optimization, and network security. At RouterHax, he oversees editorial direction and covers home networking guides, mesh WiFi system reviews, and practical troubleshooting resources for everyday users.